Two woolly monsters emigrate to Hawaii...

Here are some photos of the two woolly monster puppets I made to send to John Hankins (castlegardener) as part of the international animation co-op. They are provisionally called 'Dad' and 'Toddler'. I'm afraid the lighting and focus in the photos is not great - I took them in a hurry under yellowish a light with no flash.

The Dad is a little smaller than my usual puppets, and is about 10 inches tall, the Toddler is tiny, just over 4 inches tall, and had to be made using miniature crochet with a 1mm hook.

Both puppets have aluminium armature wire and epoxy putty armatures which I wrapped with polyfibre wadding stuck in place with Copydex latex glue (one of the most versatile mediums in the world). The skins are made of hand crocheted yarn, acrylic and wool/acrylic blend in the case of the Dad puppet, and very fine angora/lambswool blend for the Toddler. The armature for the father had to be completed in stages after certain parts of the woolly skin had been sewn into place, otherwise the hands would have been too big to pass through the 'sleeves' of the skin.

The mouths are felt replacements, and other details are made using buttons and fluffy pom-poms. As usual I used french knitting (done on a circular four-pin bobbin) for Dad's fingers, which are threaded over latex and wool wrapped wire fingers.

Props, cheap LEDs and fuzzy boobs!

I just thought I'd post some photos of various props I've made over the last few weeks. Most of them are for the international animation co-operative set up by John Hankins (castlegardener).

The first few are some wooden toys made from wooden bits and bobs I had in my hoard of useful junk:

And this is my idea of what a Bubo (Clash of the Titans) bean-bag toy would look like. He's made of painted polymer clay:


And here's another silly stop-motion reference. Two plates with sheep on (ok, so I didn't 'make' them, I just drew on two plain doll's plates with Sharpie markers, then varnished them):

The other things I've been working on are some working table-lamps. I got an bargain on some ultra-bright LEDs in a variety of colours from a website called http://www.phenoptix.co.uk/ who even sell blue and white LEDs for less than 14p each! That's ridiculously cheap, especially for those colours... I remember back when I was doing AS-level electronics in the late 90s, blue LEDs cost about £3 each and white LEDs hadn't even been invented... ahhhh, so long ago...

The website also sells great value resistors, which you need to prevent the LEDs being destroyed by the 9V circuits I wire them into. Great service too - if you need LEDs, I highly recommend them (they ship internationally too). The LEDs are really powerful (especially the white ones) and give a narrow 20 degree beam of light. They are so bright that I think I could probably use them as small spot-lights for lighting areas of my sets, which is great because they run for ages on a 9V circuit, they come in loads of colours, they don't flicker and they don't heat up!

Anyway, I used yellow LEDs in these two table lamps, to be placed in a sunny yellow coloured set. The lamps are made from glass beads and hollow wooden bases all glued together with epoxy. I soldered a 3mm yellow LED with a resistor into a circuit with a PP3 clip for a 9V battery, then covered all the exposed wires with heat-shrink tubing, with more heat-shrink over the top of that to turn the two seperate wires into one cable going from the lamp (the batteries will be hidden, obviously). I glued the LED into the bottom of the hole through the centre of the lamp, and put a 'plug' of tin foil fixed with epoxy into the hole at the top of the lamp to act as a reflector bouncing light back into the lamp.

I also made this lamp, to go in a set with a blue colour scheme, using a 3mm white LED. Most white LEDs give off a blue tinged light, and this one looks extra blue because of the blue glass in the lamp. It gives out about 3 times as much light as the yellow lamps, so I hope it won't be too overpowering!

Oh, and one last completely unrelated picture:

Yup, that's what woolly alien glamour model looks like, just in case you ever wondered...

It's for the cover of a magazine prop in 'Monday to Friday'.

If it arouses you (and you aren't a woolly alien yourself) you should probably be concerned!

Finally, some alien industral set photos!

At last, here they are, some photos of my woolly monsters in their finished alien technology set, ready to animate! The photos were taken using my new FZ50 and you can click on them to see the BIG versions on flickr:











It's probably best not to ask what the heck is going on in the last photo!